to DN16 and dimensionally suitable for the hose types* 1SC, 2SC, 1SN, 2SN, 4SP, 4SH, R13, R15. Special type 37A for 700bar hydraulic tool hoses. Compatible to all fitting types according to DIN EN 20066. More important information see on the left page.
For more information, see DIN 20066. Part no. for variable lengths and connections 4 . 500 . 1500 . 2 . 3 Hose inside diameter (mm) Operating pressure max. 500 bar Hose length (mm) Hose connection left side Hose connection right side High-pressure hoses
Stauff hose ﬁtting SHF type in all sizes must be crimped only over the crimp length indied by a circumferential ring marked on the ferrule, leaving a bubble in front. Ferrule length not to be crimped indied in the below diagram and table refers to the length from the front (pre-crimp/latch area) of the ferrule to the ring mark.
Hose length L in mm Hose connection on the left Union nut 3 = M 16 x 15. 4 = M 14 x 15. 5 = M 12 x 15. Hose connection Further information see DIN 20066 Notes on high pressure hoses The freely selectable hose lengths should be kinking, abrasion and
diameter of hose pipe) or length of the to the working process. mounting, ¡.e. are not bent directly behind the valve; i) of pipes 7.2.8 Flexible tubes Other components shall not cause an obstruction when Flexible tubes in accordance with DIN 20066 I
28/6/2018· German version EN 12111:2002+A1:2009 (16) /FABERG co-author/ DIN EN 1889-2 DIN EN 12111 FABERG Normenausschuss Bergbau Page 18 of 45 .97 Fluid-systems . 1:3 taper gauges (5) 06.92 Hose fittings. coupling nipples with round thread form (5) 10
DIN 24339 : 2016 HYDRAULIC FLUID POWER - RESERVOIRS MADE OF STEEL, NOMINAL SIZES 63 TO 2 000 - DIMENSIONS, REQUIREMENTS, TESTING DIN 20066 : 2016 HYDRAULIC FLUID POWER - HOSE ASSELIES - DIMENSIONS DIN 2445
Specifiion of the general hose dimensions is subject to DIN 20066. Date Completed by Important note: All manufacturers, importers, retailers and operators are required to comply with the Equipment and Product Safety Act, and the corresponding European
PARKER Hydraulic Technical Handbook. Very good reference for engineer, mechanics, and buyer.
*JIS B 8363, ISO/DIS 6162, DIN 20066, and SAE J518 are interchangeable, except for bolt sizes. JIS 210 Kgf/cm2 4-Bolt Square Flange 12 Approx. inch size 1/ 2 19 3/ 4 25 1 32 11/4 38 11/2 50 2 Size
Hose length L in mm Hose connection on the left Union nut 3 = M 16 x 15. 4 = M 14 x 15. 5 = M 12 x 15. Hose connection on Further information see DIN 20066 Notes on high pressure hoses The freely selectable hose lengths should be kinking, abrasion
A norm-compliant type code is generated automatically in accordance with predefinable sets of rules (such as to DIN 20066) and transferred to the selected hydraulic hose line. This normcompliant type code allows the hose line to be ordered clearly defined at any supplier.
SAE J518, DIN 20066, ISO/DIS 6162 and JIS B 8363 are all interchangeable, except for bolt sizes. NOM. FLANGE SIZE DASH SIZE BØ T F G PORT THREAD & BOLT LENGTH PORT BOLT LENGHT PORT BOLT Inch mm inch mm inch mm inch mm inch UNC
Clients can avail from us Hose Fittings in stainless steel 304 & 316 grades and brass. Our crimped & reusable end fittings are suitable for braided and spiral hoses. The ''ME'' Hose fittings comply with the standards of DIN 20066, SAE 514, DIN 7642, BS 5200-ISO WD 8434-6, DIN …
high pressure hose series Steck Max. working pressure: s up to 630 bar Pressure / t factor: at 20 C 100% at 40 C 95% at 60 C 90% series Steck series M16x2 series S12x1,5 pressure gauge connector G 1/42) length L 1) acc. DIN 20066 part nuer
Length Up to 19 m(1) Tolerances According to DIN 20066 Nominal width 4, 6, 8, 10, 13 mm (1) Available in steps of 0.1 m Heater Constructions Type Resistance heating cable Material Various alloys Material of insulation PFTE Material of outer sheath
LENGTH 315'' ALOG INTERPUMP Hydraulic Connectors HOSE AND CONNECTORS chort2ûlac anci/cr cl.cntcn. b2inc cornprcrniccd: cl:cl rninimurn b cad ''ECHNICAL INFO INTRO AND T ALOG INTERPUMP Hydraulic Connectors HOSE AND Title
hose line, we also refer you to the relevant regulations, in particular: data sheet T002 BG (German trade organisation chemical industry 9/95 (ZH 1/134)), DIN 2827 (in particular Item 8) DIN 20066 DIN 6134 Part 1 (in particular Items 9 and 11), DIN 20066 Fitting
Min/Max hose diameter OD 8-50 mm OD Max cutting length 99999 nn Max load hose reel 400 kg Cutting tolerance +/- 1 mm, enligt DIN 20066 Motor 5,5 kW 3000 rpm Servo-motor
The hoses are asseled to Hose Assely Standard DIN 20066. Type (3) Hose selection and routing per industry standard best practices (including MDG41, ISO 17165-2 and SAE J1273).
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG REPLACEMENT DIN 20066 Fluid technology - hose lines, dimensions, specifiions DIN 20163 Explosives work DIN 21800 Hammer and chisel signs (mining syol) DIN 21908 Mining crevice work; colours
Automatic cutting system Autocut 5-32CTS is an automatic cutting machine for tex-tile and steel reinforced hoses. The machine is easy to operate because of the logic control unit and LCD-display. The operation is optimized by adding the hose reel and the
DIN 20066 Fluid technology - hose lines, dimensions, specifiions DIN 20163 Explosives work DIN 21800 Hammer and chisel signs (mining syol) DIN 21908 Mining crevice work; colours DIN 22101 Conveyor belt for bulk material, fundamentals, analysis and
Requirements for fitting hoses DIN 20066 Hose fittings DIN 20078-9 Safety regulations for hydraulic hoses (ZH 1/74) T-8-PL union tee Spring pin Ø 10x50 DIN EN 28752
DIN 20066:2002-10 Although this is a German standard, it is often taken as reference in hose manufacturer standards or guidance, BGR 237 Feb 2008 – BG-Regel: Hydraulik Schlauchleitungen – Regeln für den sicheren Einsatz. 4. Lifetime
For more information, see DIN 20066. Hose inside diameter (mm) Operating pressure max.. 500 bar Hose length L (mm) Hose connection left side Hose connection right side 4 . 500 . 1500 . 2 . 3 Part no. 5.5065.0003 Hose holder made from Delrin High-pressure
Length Up to 19 m(1) Tolerances According to DIN 20066 Nominal width 4, 6, 8, 10, 13 mm (1) Available in steps of 0.1 m Heater Construction Type Resistance heating cable Material Various alloys Material of insulation PTFE Material of outer sheath Copper
Hose capacity OD 8 - 50 mm OD Cutting capacity 480-700 pcs/hour (SAE 100 R1T 3/8", 1000 mm) Max. load hose reel 400 kg Max. cutting length 99999 mm Cut tolerance (PLC-theoretic) ± 1 mm Cut tolerance 1- 2 layer hoses According to DIN 20 066
SKU: | 60.00 € | SAE 100 R7 1/4″ (200 bar) pressed tube with two 1/4″ Aisi 316L stainless steel fittings, 1x straight and 1x 90° by MCS
Min/Max hose diameter OD: 8-50 mm Cutting capacity: 480-700 pcs/hour Max load hose reel: 400 Kg Max. cutting length: 99999 mm DESIGNATION AutoCut 5-32CTS 5.5kW: 9080-01-00 ACCESSORIES HoseReel EOS w motorized uncoiling: 9080-01-08